digital西行庵 wiki - Update of U-Boot on Sheevaplug on squeeze Diff
- Added parts are displayed like this.
- Deleted parts are displayed
like this.
sheevaplug.cfg をググっていたら、squeeze, sid にはopenocd が、パッケージとして存在するらしい。
http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/i386/iso-cd/debian-testing-i386-netinst.iso
をダウンロードし、CD-ROMを焼き焼きして、
!squeezeをクリーンインストール後、
squeeze:/home/nitobe# cat /etc/debian_version
squeeze/sid
squeeze:/home/nitobe# uname -a
Linux squeeze 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:38 UTC 2009 i686 GNU/Linux
squeeze:/home/nitobe# aptitude install libusb-dev libftdi-dev libboost-dev openocd
squeeze:/home/nitobe# find /usr -name sheevaplug.cfg -print
/usr/share/openocd/scripts/interface/sheevaplug.cfg
/usr/share/openocd/scripts/board/sheevaplug.cfg
既に、cfgファイルは、/usr/share/openocd/scripts/board/ に存在する。
squeeze:/home/nitobe# openocd -f /usr/share/openocd/scripts/board/sheevaplug
Open On-Chip Debugger 0.2.0-in-development (2009-06-25-18:22) svn:r2403
BUGS? Read /usr/share/doc/openocd/BUGS
$URL: http://svn.berlios.de/svnroot/repos/openocd/trunk/src/openocd.c $
2000 kHz
jtag_nsrst_delay: 200
jtag_ntrst_delay: 200
dcc downloads are enabled
Info : JTAG tap: feroceon.cpu tap/device found: 0x20a023d3 (mfg: 0x1e9, part: 0x0a02, ver: 0x2)
Info : JTAG Tap/device matched
おっ！さくっと動くねぇ。
違うターミナルをあげて、
squeeze:/home/nitobe# telnet localhost 4444
Trying ::1...
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
Open On-Chip Debugger
> help
bp set breakpoint <address> <length> [hw]
cpu <name> - prints out target options and a comment
on CPU which matches name
debug_level adjust debug level <0-3>
drscan execute DR scan <device> <num_bits> <value>
<num_bits1> <value2> ...
dump_image dump_image <file> <address> <size>
exit exit telnet session
fast fast <enable/disable> - place at beginning of
config files. Sets defaults to fast and dangerous.
fast_load loads active fast load image to current target -
mainly for profiling purposes
fast_load_image same args as load_image, image stored in memory -
mainly for profiling purposes
find <file> - print full path to file according to
OpenOCD search rules
flush_count returns number of times the JTAG queue has been
flushed
ft2232_device_desc the USB device description of the FTDI FT2232
device
ft2232_latency set the FT2232 latency timer to a new value
ft2232_layout the layout of the FT2232 GPIO signals used to
control output-enables and reset signals
ft2232_serial the serial number of the FTDI FT2232 device
ft2232_vid_pid the vendor ID and product ID of the FTDI FT2232
device
gdb_breakpoint_override hard/soft/disable - force breakpoint type for gdb
'break' commands.
gdb_detach resume/reset/halt/nothing - specify behavior when
GDB detaches from the target
gdb_flash_program enable or disable flash program
gdb_memory_map enable or disable memory map
gdb_port daemon configuration command gdb_port
gdb_report_data_abort enable or disable reporting data aborts
halt halt target
help Tcl implementation of help command
init initializes target and servers - nop on subsequent
invocations
interface try to configure interface
interface_list list all built-in interfaces
irscan execute IR scan <device> <instr> [dev2] [instr2]
...
jtag perform jtag tap actions
jtag_device (DEPRECATED) jtag_device <ir_length> <ir_expected>
<ir_mask>
jtag_khz set maximum jtag speed (if supported); parameter
is maximum khz, or 0 for adaptive clocking (RTCK).
jtag_nsrst_delay jtag_nsrst_delay <ms> - delay after deasserting
srst in ms
jtag_ntrst_delay jtag_ntrst_delay <ms> - delay after deasserting
trst in ms
jtag_rclk fallback_speed_khz - set JTAG speed to RCLK or use
fallback speed
jtag_reset toggle reset lines <trst> <srst>
jtag_speed (DEPRECATED) set jtag speed (if supported)
load_image load_image <file> <address>
['bin'|'ihex'|'elf'|'s19'] [min_address]
[max_length]
log_output redirect logging to <file> (default: stderr)
mdb display memory bytes <addr> [count]
mdh display memory half-words <addr> [count]
mdw display memory words <addr> [count]
mwb write memory byte <addr> <value> [count]
mwh write memory half-word <addr> <value> [count]
mww write memory word <addr> <value> [count]
ocd_array2mem convert a TCL array to memory locations and write
the values <ARRAYNAME> <WIDTH = 32/16/8>
<ADDRESS> <COUNT>
ocd_flash_banks return information about the flash banks
ocd_mem2array read memory and return as a TCL array for script
processing <ARRAYNAME> <WIDTH = 32/16/8> <ADDRESS>
<COUNT>
pathmove move JTAG to state1 then to state2, state3, etc.
<state1>,<state2>,<stat3>...
poll poll target state
power_restore Overridable procedure run when power restore is
detected. Runs 'reset init' by default.
production <serialnumber> - Runs production procedure. Throws
exception if procedure failed. Prints progress
messages. Implement this procedure in the target
script.
production Runs test procedure. Throws exception if procedure
failed. Prints progress messages. Implement in
target script.
production_info Displays information on production procedure for
target script. Implement this procedure in target
script.
profile profiling samples the CPU PC
rbp remove breakpoint <adress>
reg display or set a register
reset reset target [run | halt | init] - default is run
reset_config [none/trst_only/srst_only/trst_and_srst]
[srst_pulls_trst/trst_pulls_srst]
[combined/separate]
[trst_push_pull/trst_open_drain]
[srst_push_pull/srst_open_drain]
resume resume target [addr]
runtest move to Run-Test/Idle, and execute <num_cycles>
rwp remove watchpoint <adress>
scan_chain print current scan chain configuration
script <filename> - filename of OpenOCD script (tcl) to
run
shutdown shut the server down
sleep <n> [busy] - sleep for n milliseconds. "busy"
means busy wait
soft_reset_halt halt the target and do a soft reset
srst_deasserted Overridable procedure run when srst deassert is
detected. Runs 'reset init' by default.
step step one instruction from current PC or [addr]
svf run svf <file>
target configure target
targets change the current command line target (one
parameter) or lists targets (with no parameter)
tcl_port port on which to listen for incoming TCL syntax
telnet_port port on which to listen for incoming telnet
connections
test_image test_image <file> [offset] [type]
tms_sequence choose short(default) or long tms_sequence <short
| long>
verify_image verify_image <file> [offset] [type]
verify_ircapture verify value captured during Capture-IR <enable |
disable>
verify_jtag verify value capture <enable | disable>
version show OpenOCD version
virt2phys translate a virtual address into a physical
address
wait_halt wait for target halt [time (s)]
wp set watchpoint <address> <length> <r/w/a> [value]
[mask]
xsvf run xsvf <file> [virt2] [quiet]
arm7_9 dbgrq use EmbeddedICE dbgrq instead of breakpoint for
target halt requests <enable | disable>
arm7_9 dcc_downloads use DCC downloads for larger memory writes <enable
| disable>
arm7_9 fast_memory_access use fast memory accesses instead of slower but
potentially safer accesses <enable | disable>
arm7_9 write_core_reg write core register <num> <mode> <value>
arm7_9 write_xpsr_im8 write program status register <8bit immediate>
<rotate> <not cpsr | spsr>
arm7_9 write_xpsr write program status register <value> <not cpsr |
spsr>
arm926ejs cache_info display information about target caches
arm926ejs cp15 display/modify cp15 register <opcode_1> <opcode_2>
<CRn> <CRm> [value]
arm926ejs mdb_phys display memory bytes <physical addr> [count]
arm926ejs mdh_phys display memory half-words <physical addr> [count]
arm926ejs mdw_phys display memory words <physical addr> [count]
arm926ejs mwb_phys write memory byte <physical addr> <value>
arm926ejs mwh_phys write memory half-word <physical addr> <value>
arm926ejs mww_phys write memory word <physical addr> <value>
arm926ejs virt2phys translate va to pa <va>
arm9tdmi vector_catch catch arm920t vectors ['all'|'none'|'<vec1 vec2
...>']
armv4_5 core_state display/change ARM core state <arm | thumb>
armv4_5 disassemble disassemble instructions <address> <count>
['thumb']
armv4_5 reg display ARM core registers
etm config etm config <target> <port_width> <port_mode>
<clocking> <capture_driver>
flash bank flash bank <driver> <base> <size> <chip_width>
<bus_width> <target> [driver_options ...]
mflash bank mflash bank <soc> <base> <RST pin> <target #>
nand check_bad_blocks check NAND flash device <num> for bad blocks
[<offset> <length>]
nand device
nand dump dump from NAND flash device <num> <filename>
<offset> <length> [oob_raw | oob_only]
nand erase erase blocks on NAND flash device <num> <offset>
<length>
nand info print info about NAND flash device <num>
nand list list configured NAND flash devices
nand probe identify NAND flash device <num>
nand raw_access raw access to NAND flash device <num>
['enable'|'disable']
nand write write to NAND flash device <num> <filename>
<offset> [oob_raw | oob_only | oob_softecc |
oob_softecc_kw]
pld device
target_request debugmsgs enable/disable reception of debug messages from
target
trace history display trace history, ['clear'] history or set
[size]
trace point display trace points, ['clear'] list of trace
points, or add new tracepoint at [address]
> cpu
CPU Options Comment
> trace history
trace history buffer is not allocated
> reg
(0) r0 (/32): 0x00000000 (dirty: 0, valid: 0)
(1) r1 (/32): 0x00000000 (dirty: 0, valid: 0)
(2) r2 (/32): 0x00000000 (dirty: 0, valid: 0)
(3) r3 (/32): 0x00000000 (dirty: 0, valid: 0)
(4) r4 (/32): 0x00000000 (dirty: 0, valid: 0)
(5) r5 (/32): 0x00000000 (dirty: 0, valid: 0)
(6) r6 (/32): 0x00000000 (dirty: 0, valid: 0)
(7) r7 (/32): 0x00000000 (dirty: 0, valid: 0)
(8) r8 (/32): 0x00000000 (dirty: 0, valid: 0)
(9) r9 (/32): 0x00000000 (dirty: 0, valid: 0)
(10) r10 (/32): 0x00000000 (dirty: 0, valid: 0)
(11) r11 (/32): 0x00000000 (dirty: 0, valid: 0)
(12) r12 (/32): 0x00000000 (dirty: 0, valid: 0)
(13) r13_usr (/32): 0x00000000 (dirty: 0, valid: 0)
(14) lr_usr (/32): 0x00000000 (dirty: 0, valid: 0)
(15) pc (/32): 0x00000000 (dirty: 0, valid: 0)
(16) r8_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(17) r9_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(18) r10_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(19) r11_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(20) r12_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(21) r13_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(22) lr_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(23) r13_irq (/32): 0x00000000 (dirty: 0, valid: 0)
(24) lr_irq (/32): 0x00000000 (dirty: 0, valid: 0)
(25) r13_svc (/32): 0x00000000 (dirty: 0, valid: 0)
(26) lr_svc (/32): 0x00000000 (dirty: 0, valid: 0)
(27) r13_abt (/32): 0x00000000 (dirty: 0, valid: 0)
(28) lr_abt (/32): 0x00000000 (dirty: 0, valid: 0)
(29) r13_und (/32): 0x00000000 (dirty: 0, valid: 0)
(30) lr_und (/32): 0x00000000 (dirty: 0, valid: 0)
(31) cpsr (/32): 0x00000000 (dirty: 0, valid: 0)
(32) spsr_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(33) spsr_irq (/32): 0x00000000 (dirty: 0, valid: 0)
(34) spsr_svc (/32): 0x00000000 (dirty: 0, valid: 0)
(35) spsr_abt (/32): 0x00000000 (dirty: 0, valid: 0)
(36) spsr_und (/32): 0x00000000 (dirty: 0, valid: 0)
(37) debug_ctrl (/6): 0x00 (dirty: 0, valid: 0)
(38) debug_status (/5): 0x04 (dirty: 0, valid: 0)
(39) comms_ctrl (/32): 0x00000018 (dirty: 0, valid: 0)
(40) comms_data (/32): 0x00000000 (dirty: 0, valid: 0)
(41) watch 0 addr value (/32): 0x00000000 (dirty: 0, valid: 0)
(42) watch 0 addr mask (/32): 0x00000000 (dirty: 0, valid: 0)
(43) watch 0 data value (/32): 0x00000000 (dirty: 0, valid: 0)
(44) watch 0 data mask (/32): 0x00000000 (dirty: 0, valid: 0)
(45) watch 0 control value (/32): 0x00000000 (dirty: 0, valid: 0)
(46) watch 0 control mask (/32): 0x00000000 (dirty: 0, valid: 0)
(47) watch 1 addr value (/32): 0x00000000 (dirty: 0, valid: 0)
(48) watch 1 addr mask (/32): 0x00000000 (dirty: 0, valid: 0)
(49) watch 1 data value (/32): 0x00000000 (dirty: 0, valid: 0)
(50) watch 1 data mask (/32): 0x00000000 (dirty: 0, valid: 0)
(51) watch 1 control value (/32): 0x00000000 (dirty: 0, valid: 0)
(52) watch 1 control mask (/32): 0x00000000 (dirty: 0, valid: 0)
(53) vector catch (/32): 0x00000000 (dirty: 0, valid: 1)
>
ほんとかいな？わかちこわかちこ。
!実は
squeezeをクリーンインストールする前に、以前のlennyをfull-upgradeして、sidも試してみた。カーネルが2.6.30で、openocdもsvn:r2529と、更に新しいものを使っている。sidでもopenocdがさくっと動いたことを報告しておこう。度胸のある方はsidを飼いならしてみてはいかが？
http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/i386/iso-cd/debian-testing-i386-netinst.iso
をダウンロードし、CD-ROMを焼き焼きして、
!squeezeをクリーンインストール後、
squeeze:/home/nitobe# cat /etc/debian_version
squeeze/sid
squeeze:/home/nitobe# uname -a
Linux squeeze 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:38 UTC 2009 i686 GNU/Linux
squeeze:/home/nitobe# aptitude install libusb-dev libftdi-dev libboost-dev openocd
squeeze:/home/nitobe# find /usr -name sheevaplug.cfg -print
/usr/share/openocd/scripts/interface/sheevaplug.cfg
/usr/share/openocd/scripts/board/sheevaplug.cfg
既に、cfgファイルは、/usr/share/openocd/scripts/board/ に存在する。
squeeze:/home/nitobe# openocd -f /usr/share/openocd/scripts/board/sheevaplug
Open On-Chip Debugger 0.2.0-in-development (2009-06-25-18:22) svn:r2403
BUGS? Read /usr/share/doc/openocd/BUGS
$URL: http://svn.berlios.de/svnroot/repos/openocd/trunk/src/openocd.c $
2000 kHz
jtag_nsrst_delay: 200
jtag_ntrst_delay: 200
dcc downloads are enabled
Info : JTAG tap: feroceon.cpu tap/device found: 0x20a023d3 (mfg: 0x1e9, part: 0x0a02, ver: 0x2)
Info : JTAG Tap/device matched
おっ！さくっと動くねぇ。
違うターミナルをあげて、
squeeze:/home/nitobe# telnet localhost 4444
Trying ::1...
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
Open On-Chip Debugger
> help
bp set breakpoint <address> <length> [hw]
cpu <name> - prints out target options and a comment
on CPU which matches name
debug_level adjust debug level <0-3>
drscan execute DR scan <device> <num_bits> <value>
<num_bits1> <value2> ...
dump_image dump_image <file> <address> <size>
exit exit telnet session
fast fast <enable/disable> - place at beginning of
config files. Sets defaults to fast and dangerous.
fast_load loads active fast load image to current target -
mainly for profiling purposes
fast_load_image same args as load_image, image stored in memory -
mainly for profiling purposes
find <file> - print full path to file according to
OpenOCD search rules
flush_count returns number of times the JTAG queue has been
flushed
ft2232_device_desc the USB device description of the FTDI FT2232
device
ft2232_latency set the FT2232 latency timer to a new value
ft2232_layout the layout of the FT2232 GPIO signals used to
control output-enables and reset signals
ft2232_serial the serial number of the FTDI FT2232 device
ft2232_vid_pid the vendor ID and product ID of the FTDI FT2232
device
gdb_breakpoint_override hard/soft/disable - force breakpoint type for gdb
'break' commands.
gdb_detach resume/reset/halt/nothing - specify behavior when
GDB detaches from the target
gdb_flash_program enable or disable flash program
gdb_memory_map enable or disable memory map
gdb_port daemon configuration command gdb_port
gdb_report_data_abort enable or disable reporting data aborts
halt halt target
help Tcl implementation of help command
init initializes target and servers - nop on subsequent
invocations
interface try to configure interface
interface_list list all built-in interfaces
irscan execute IR scan <device> <instr> [dev2] [instr2]
...
jtag perform jtag tap actions
jtag_device (DEPRECATED) jtag_device <ir_length> <ir_expected>
<ir_mask>
jtag_khz set maximum jtag speed (if supported); parameter
is maximum khz, or 0 for adaptive clocking (RTCK).
jtag_nsrst_delay jtag_nsrst_delay <ms> - delay after deasserting
srst in ms
jtag_ntrst_delay jtag_ntrst_delay <ms> - delay after deasserting
trst in ms
jtag_rclk fallback_speed_khz - set JTAG speed to RCLK or use
fallback speed
jtag_reset toggle reset lines <trst> <srst>
jtag_speed (DEPRECATED) set jtag speed (if supported)
load_image load_image <file> <address>
['bin'|'ihex'|'elf'|'s19'] [min_address]
[max_length]
log_output redirect logging to <file> (default: stderr)
mdb display memory bytes <addr> [count]
mdh display memory half-words <addr> [count]
mdw display memory words <addr> [count]
mwb write memory byte <addr> <value> [count]
mwh write memory half-word <addr> <value> [count]
mww write memory word <addr> <value> [count]
ocd_array2mem convert a TCL array to memory locations and write
the values <ARRAYNAME> <WIDTH = 32/16/8>
<ADDRESS> <COUNT>
ocd_flash_banks return information about the flash banks
ocd_mem2array read memory and return as a TCL array for script
processing <ARRAYNAME> <WIDTH = 32/16/8> <ADDRESS>
<COUNT>
pathmove move JTAG to state1 then to state2, state3, etc.
<state1>,<state2>,<stat3>...
poll poll target state
power_restore Overridable procedure run when power restore is
detected. Runs 'reset init' by default.
production <serialnumber> - Runs production procedure. Throws
exception if procedure failed. Prints progress
messages. Implement this procedure in the target
script.
production Runs test procedure. Throws exception if procedure
failed. Prints progress messages. Implement in
target script.
production_info Displays information on production procedure for
target script. Implement this procedure in target
script.
profile profiling samples the CPU PC
rbp remove breakpoint <adress>
reg display or set a register
reset reset target [run | halt | init] - default is run
reset_config [none/trst_only/srst_only/trst_and_srst]
[srst_pulls_trst/trst_pulls_srst]
[combined/separate]
[trst_push_pull/trst_open_drain]
[srst_push_pull/srst_open_drain]
resume resume target [addr]
runtest move to Run-Test/Idle, and execute <num_cycles>
rwp remove watchpoint <adress>
scan_chain print current scan chain configuration
script <filename> - filename of OpenOCD script (tcl) to
run
shutdown shut the server down
sleep <n> [busy] - sleep for n milliseconds. "busy"
means busy wait
soft_reset_halt halt the target and do a soft reset
srst_deasserted Overridable procedure run when srst deassert is
detected. Runs 'reset init' by default.
step step one instruction from current PC or [addr]
svf run svf <file>
target configure target
targets change the current command line target (one
parameter) or lists targets (with no parameter)
tcl_port port on which to listen for incoming TCL syntax
telnet_port port on which to listen for incoming telnet
connections
test_image test_image <file> [offset] [type]
tms_sequence choose short(default) or long tms_sequence <short
| long>
verify_image verify_image <file> [offset] [type]
verify_ircapture verify value captured during Capture-IR <enable |
disable>
verify_jtag verify value capture <enable | disable>
version show OpenOCD version
virt2phys translate a virtual address into a physical
address
wait_halt wait for target halt [time (s)]
wp set watchpoint <address> <length> <r/w/a> [value]
[mask]
xsvf run xsvf <file> [virt2] [quiet]
arm7_9 dbgrq use EmbeddedICE dbgrq instead of breakpoint for
target halt requests <enable | disable>
arm7_9 dcc_downloads use DCC downloads for larger memory writes <enable
| disable>
arm7_9 fast_memory_access use fast memory accesses instead of slower but
potentially safer accesses <enable | disable>
arm7_9 write_core_reg write core register <num> <mode> <value>
arm7_9 write_xpsr_im8 write program status register <8bit immediate>
<rotate> <not cpsr | spsr>
arm7_9 write_xpsr write program status register <value> <not cpsr |
spsr>
arm926ejs cache_info display information about target caches
arm926ejs cp15 display/modify cp15 register <opcode_1> <opcode_2>
<CRn> <CRm> [value]
arm926ejs mdb_phys display memory bytes <physical addr> [count]
arm926ejs mdh_phys display memory half-words <physical addr> [count]
arm926ejs mdw_phys display memory words <physical addr> [count]
arm926ejs mwb_phys write memory byte <physical addr> <value>
arm926ejs mwh_phys write memory half-word <physical addr> <value>
arm926ejs mww_phys write memory word <physical addr> <value>
arm926ejs virt2phys translate va to pa <va>
arm9tdmi vector_catch catch arm920t vectors ['all'|'none'|'<vec1 vec2
...>']
armv4_5 core_state display/change ARM core state <arm | thumb>
armv4_5 disassemble disassemble instructions <address> <count>
['thumb']
armv4_5 reg display ARM core registers
etm config etm config <target> <port_width> <port_mode>
<clocking> <capture_driver>
flash bank flash bank <driver> <base> <size> <chip_width>
<bus_width> <target> [driver_options ...]
mflash bank mflash bank <soc> <base> <RST pin> <target #>
nand check_bad_blocks check NAND flash device <num> for bad blocks
[<offset> <length>]
nand device
nand dump dump from NAND flash device <num> <filename>
<offset> <length> [oob_raw | oob_only]
nand erase erase blocks on NAND flash device <num> <offset>
<length>
nand info print info about NAND flash device <num>
nand list list configured NAND flash devices
nand probe identify NAND flash device <num>
nand raw_access raw access to NAND flash device <num>
['enable'|'disable']
nand write write to NAND flash device <num> <filename>
<offset> [oob_raw | oob_only | oob_softecc |
oob_softecc_kw]
pld device
target_request debugmsgs enable/disable reception of debug messages from
target
trace history display trace history, ['clear'] history or set
[size]
trace point display trace points, ['clear'] list of trace
points, or add new tracepoint at [address]
> cpu
CPU Options Comment
> trace history
trace history buffer is not allocated
> reg
(0) r0 (/32): 0x00000000 (dirty: 0, valid: 0)
(1) r1 (/32): 0x00000000 (dirty: 0, valid: 0)
(2) r2 (/32): 0x00000000 (dirty: 0, valid: 0)
(3) r3 (/32): 0x00000000 (dirty: 0, valid: 0)
(4) r4 (/32): 0x00000000 (dirty: 0, valid: 0)
(5) r5 (/32): 0x00000000 (dirty: 0, valid: 0)
(6) r6 (/32): 0x00000000 (dirty: 0, valid: 0)
(7) r7 (/32): 0x00000000 (dirty: 0, valid: 0)
(8) r8 (/32): 0x00000000 (dirty: 0, valid: 0)
(9) r9 (/32): 0x00000000 (dirty: 0, valid: 0)
(10) r10 (/32): 0x00000000 (dirty: 0, valid: 0)
(11) r11 (/32): 0x00000000 (dirty: 0, valid: 0)
(12) r12 (/32): 0x00000000 (dirty: 0, valid: 0)
(13) r13_usr (/32): 0x00000000 (dirty: 0, valid: 0)
(14) lr_usr (/32): 0x00000000 (dirty: 0, valid: 0)
(15) pc (/32): 0x00000000 (dirty: 0, valid: 0)
(16) r8_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(17) r9_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(18) r10_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(19) r11_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(20) r12_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(21) r13_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(22) lr_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(23) r13_irq (/32): 0x00000000 (dirty: 0, valid: 0)
(24) lr_irq (/32): 0x00000000 (dirty: 0, valid: 0)
(25) r13_svc (/32): 0x00000000 (dirty: 0, valid: 0)
(26) lr_svc (/32): 0x00000000 (dirty: 0, valid: 0)
(27) r13_abt (/32): 0x00000000 (dirty: 0, valid: 0)
(28) lr_abt (/32): 0x00000000 (dirty: 0, valid: 0)
(29) r13_und (/32): 0x00000000 (dirty: 0, valid: 0)
(30) lr_und (/32): 0x00000000 (dirty: 0, valid: 0)
(31) cpsr (/32): 0x00000000 (dirty: 0, valid: 0)
(32) spsr_fiq (/32): 0x00000000 (dirty: 0, valid: 0)
(33) spsr_irq (/32): 0x00000000 (dirty: 0, valid: 0)
(34) spsr_svc (/32): 0x00000000 (dirty: 0, valid: 0)
(35) spsr_abt (/32): 0x00000000 (dirty: 0, valid: 0)
(36) spsr_und (/32): 0x00000000 (dirty: 0, valid: 0)
(37) debug_ctrl (/6): 0x00 (dirty: 0, valid: 0)
(38) debug_status (/5): 0x04 (dirty: 0, valid: 0)
(39) comms_ctrl (/32): 0x00000018 (dirty: 0, valid: 0)
(40) comms_data (/32): 0x00000000 (dirty: 0, valid: 0)
(41) watch 0 addr value (/32): 0x00000000 (dirty: 0, valid: 0)
(42) watch 0 addr mask (/32): 0x00000000 (dirty: 0, valid: 0)
(43) watch 0 data value (/32): 0x00000000 (dirty: 0, valid: 0)
(44) watch 0 data mask (/32): 0x00000000 (dirty: 0, valid: 0)
(45) watch 0 control value (/32): 0x00000000 (dirty: 0, valid: 0)
(46) watch 0 control mask (/32): 0x00000000 (dirty: 0, valid: 0)
(47) watch 1 addr value (/32): 0x00000000 (dirty: 0, valid: 0)
(48) watch 1 addr mask (/32): 0x00000000 (dirty: 0, valid: 0)
(49) watch 1 data value (/32): 0x00000000 (dirty: 0, valid: 0)
(50) watch 1 data mask (/32): 0x00000000 (dirty: 0, valid: 0)
(51) watch 1 control value (/32): 0x00000000 (dirty: 0, valid: 0)
(52) watch 1 control mask (/32): 0x00000000 (dirty: 0, valid: 0)
(53) vector catch (/32): 0x00000000 (dirty: 0, valid: 1)
>
ほんとかいな？わかちこわかちこ。
!実は
squeezeをクリーンインストールする前に、以前のlennyをfull-upgradeして、sidも試してみた。カーネルが2.6.30で、openocdもsvn:r2529と、更に新しいものを使っている。sidでもopenocdがさくっと動いたことを報告しておこう。度胸のある方はsidを飼いならしてみてはいかが？